惠普绘图仪维修方法--DJ1050 DJ1055CM 绘图仪滴墨传感器校准方法(2)

热门标签:

打印机复印机绘图仪维修服务站
QQ：601401952
电话：13971033338
电话：18971047950
旺旺：shizh38
网址：http://www.echao8.com

惠普绘图仪维修方法--DJ1050 DJ1055CM 绘图仪滴墨传感器校准方法(2)

发布时间：2018-11-10 22:01 浏览次数：次　　

以下是相应的原文： System Error: 0C0032 ( Continuable) Problem Description: Drop Detector not Calibrated for all Printheads. Corrective Action: Try the following: n Perform the Service Station Calibr

以下是相应的原文：
System Error: 0C0032 (Continuable)
Problem Description:Drop Detector not Calibrated for all Printheads.
Corrective Action: Try the following:
n Perform the Service Station Calibration Þ Page 5-11.
n Replace the Drop Detector Assembly Þ Page 8-10.
n If the Error Code continues, replace the Electronics Module Þ
Page 8-25.
WARNING Only replace one component at a time and check if the error has
gone before replacing another component. Using this procedure
you will be able to determine exactly which component failed.

Entering the Service Calibrations Menu
1 Once the message "Ready" is displayed on the front-panel, scroll to
the "Printer Setup Options" icon and press the Enter key.

2 Once inside the "Printer Setup Options" menu, use the Arrow keys
to scroll to the "Utilities" menu display and press the Enter key.

Make sure that you are in the Full menu mode because otherwise
you will not be able to access the "Service Tools" submenu.
3 Once inside the "Utilities" menu, press the UP and Enter keys
together. You are now in the Service Tools Menu.

4 Use the Arrow keys to scroll to the "Service Calibrations" menu
and press the Enter key.

5 Use the Arrow keys to scroll through the "Service Calibrations"
selections.

6 Press the Enter key to begin a specific calibration when the
required Service Calibration is highlighted.

If the printer is not used for 3 minutes, the printer exits out of the
Service Calibrations Menu and you must repeat the above steps
to enter Service Calibrations again.
NOTE In some cases a quick press of a button may not be recognized by
the Printer. When pressing a button, be sure to press it
deliberately and all the way to the bottom of its travel.
NOTE If the Printer hangs up during an operation, switch the Printer
OFF and restart from step 1.

Perform the Service Station Calibration as follows:
NOTE Make sure you load media bigger than A4 in to the Printer before
performing this calibration. Do NOT use any other type of media
apart from HP Coated or HP High Gloss Photo Paper.
1 In the Service Calibrations submenu, scroll to "3. Service Station"
and press Enter.

2 The following message will appear asking you to confirm the operation.
Select ACCEPT if you want to continue the Service Station Calibration, or
select CANCEL if you want to cancel the it. Press Enter once the selection
has been made.

3 If you selected to continue, then the following message appears on
the front panel if media is not loaded. You must load Media in to the
Printer to continue.

4 The Printer will start to print the calibration pattern and the
following messages will be displayed on the front panel:

5 Once the service station calibration is completed, the following
message will be displayed on the front panel:

6 To check if the Calibration was completed correctly, print the
Service Configuration Print (see Page 1-19) and check that the
calibrations are done and are within the stated limits.

武汉打印机复印机绘图仪维修服务台专注打印机复印机绘图仪的应用以及故障排除和维修；武汉打印机复印机绘图仪维修服务台收集了这些设备的一般常识性问题和技术性问题及其解决方案；同时收集了部分打印机、复印机和绘图仪维修手册，以供需要者参考和研究之用。通过浏览查阅本站相关内容，可以解决在使用过程中遇到的某些故障和使用问题。本站资深工程师从事办公设备维修近二十年，尤其是对惠普大幅面打印机绘图仪的维修服务，具有丰富的售后维修服务经验。我们专业提供湖北武汉周边地区惠普绘图仪快速上门维修服务。对其他地区用户提供远程维修咨询服务。
我们的联系方式：
电话：13971033338（微信同号，联系时请备注服务咨询）
电话：18971047950
QQ：601401952（联系时请备注服务咨询）

本文相关标签（点击标签可显示包含相同标签的文章）：

上一篇：惠普T120 T520提示马上需要维护工具包1如何处理
下一篇：惠普绘图仪打印的关键技术--打印头热发泡技术

在线客服

热门标签:

本文相关标签（点击标签可显示包含相同标签的文章）：